This is where we keep our download links for K-charts, Firmware, software etc. The links will take you to our server on Dropbox where we store all large files. Dropbox is a cloud system that provides server storage for companies to store large files. Small files can be sent via an attachment to an email message but large files (typically greater than 10 meg) cannot be sent this way so we upload our large files to the Dropbox cloud and by following the link that Dropbox gives to us for each file that we save on their server you are able to download the file from Dropbox. This service is completely free to you. Download speed will depend upon your own internet speed.
What you will able to download from this site:
Firmware upgrades
K-chart3.2 downloads
K-chart 2 downloads
Other software for Onwa products under construction
Tips and general stuff about using Onwa products under construction
Apart from providing links to download the files we also provide explanation, guidance, and tips that we feel may help you to complete the download process and also, where a software application may not be completely straightforward to use, some guidance through the process. If you are downloading files and software and you feel that an explanation is needed where it isn’t provided or that our explanation could be improved please message me, Alan Vick, either by way of a message on this website or by email to alanvick@avesmarine.com. ‘Tips and other general stuff’ is something we will be developing so if you have any questions regarding using an Onwa product please let me know so that this can be included.
Downloading and installing the files.
Click the link button. You will be presented with a .tuf file (for firmware and charts). Download the file. In your downloads list see the file (note that you cannot open .tuf files as Window will not recognise them). Copy the file and save to an SD card, up to 16gb is OK. When saved, place into your plotters card reader. Power on the plotter and the update will be recognised before the plotter boots. Accept the upgrade and the file will load into your plotter. When completed switch off and remove the SD card.
FIRMWARE: this edition of firmware was released in December 2022
K-combo later G versions – check the serial no. of your ONWA KCombo-7, if after the model number, there is a letter G, then it is a G hardware Version. G versions have different sounder hardware. Be careful that you use the right K-combo version
As KP series models have been in production for many years it is necessary to identify the version that you have:
Mk1 in production until 2018 – Mk1 can be identified by looking at the available chart choice options in the menu. Mk1 can use only C-Map and K-chart2.
Mk2 version, 2018-2020, Mk2 can be identified by looking at the available chart choice options in the menu. Mk2 can also use Navionics and K-chart3, no USB socket on back.
MK3 and Mk4 in production since 2020. Can be identified by having a USB socket on the back. No USB means that the 8299 or 1299 is either a Mk2 or even a Mk1 version.
If you are unsure – please call AVES Marine Support on 01357 680054 or, if outside UK, 44 1357 680054
Some versions of Mk3 and Mk4 KP1299 (all variants) may not accept an update to current firmware. If your 1299 Mk3 or 4 will not respond to the new firmware a small file is needed to be loaded into the plotter first before loading firmware.
Procedure: Download the small file to an SD card, put the SD card into the plotters’ card reader and start the plotter. File will be loaded. Proceed then with the actual firmware upgrade.
K-chart downloads.
K-charts were introduced in 2018 as K-chart3.1 built in charts to replace K-chart2. The K3.1 charts are generally better for most areas than K-chart2. Unfortunately the size and complexity of the K-chart3.1 produced quite serious lag when used in 7 inch models. Kp38 and 39 particularly were slowed to the point where the plotters were difficult to use. K-combo and Kp708 versions with their better hardware were usable and KP1299 models with their very superior hardware and memory were OK. In 2022 there was an improvement in the design of the K-chart to version 3.2. This was in the form of a ‘tweak’ to the charts which improved the lag across the whole model range although for KP38 and KP39, whilst improved, it is still noticeable.
To activate K-chart3.2 requires a menu change – change map choice to K-shart3. If you have been using an SD card version of K-chart2 then you also must change map source to built in.
Here are the links for K-chart3.2:note that the area images covered by each chart is for version 3.1 and may be slightly smaller since the 3.2 change
Europe
Kchart version 3 Click a button to download the K3.2 chart
200A and 200AS programming software PDF showing AIS set-up
How to program the 200A and 200AS, note that this procedure requires a serial to USB dongle that works – many don’t and the process will fail. This is why AVES Marine provides a free programming service to anyone who buys from us. We have serial dongles that work if you want to program your 200A/AS
This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.
Strictly Necessary Cookies
Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.
If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.
3rd Party Cookies
This website uses Google Analytics to collect anonymous information such as the number of visitors to the site, and the most popular pages.
Keeping this cookie enabled helps us to improve our website.
Please enable Strictly Necessary Cookies first so that we can save your preferences!